Silverware Drawer Organizer

Silverware Drawer Organizer – Our kitchen silverware drawer had a plastic organizer that left a lot of wasted space, making it hard to find things, with drawer contents that looked like a mixed up mess.
20160910_085940

Steve Ramsey from Woodworking for Mere Mortals had a great solution, an easy to make silverware drawer organizer that could be made from a single 6’ x 4” board.  We chose Maple to match the existing cabinet interior.  Steve mentioned in his blog that this was his third generation silverware organizer and shared the tips he learned and improved from the previous ones he built.  As always, Steve does a fantastic job breaking down the project into easy to follow steps (that even mere mortals can do).

Sizing the Compartments Using Shop Scraps – We used scraps and tape to model the spacing for each of the compartments.  This allowed us to mock up dimensions that worked best before we made cuts to the maple board.20160902_231252

Now that we had our dimension, we cut the boards.  The inside organizers have a semi circle cut out that makes it easy to grab the silverware.  Steve illustrates a simple method for making a precise curve using a thin piece of lumber and a string.  Too clever.20160903_204131By ripping the ¾” board into a two pieces we are able to reduce the amount of boards needed. The wider portion of each ripped board is used for the outside frame, while the thinner board is used for the inside compartment.  Notice how the inside compartment is curved so you can easily reach the silverware.20160903_210157

Once the curves are cut from each inside compartment, we now have all pieces cut and ready for assembly.  Here’s a quick video that shows how everything fits together before gluing and nailing.

This was a super fun project and provides a drawer organizer that is custom fit.  It provides the stock drawer features that are found in custom high-end cabinet drawers,

Voila! Final Result – once glued and nailed.  Let’s do this again.20160910_095003

Kitchen Cabinet Makeover… On a Tight Budget

We decided the kitchen needed a fresh look. The cabinets were in fine shape but bland, and lacking features common with custom cabinets.   We used A Rustoleum Cabinet Transformations kit in that we had some left over from a previous project.  A quality cabinet or trim paint would have worked fine as well.  

20160709_115524For us, refinishing the cabinets was a thee step process…

  1. Prep and paint the cabinet frame.
  2. Prep and paint the cabinet doors.
  3. Install door / drawer handles (our cabinets didn’t have any)

We decided the island was a great place to start.kitchencabinetcompare

We painted the cabinet frames by hand and sprayed the doors (front and back) with an HVLP sprayer and were really pleased with how it turned out.  The nice thing about spraying the doors is that it goes A LOT faster.  To provide increased durability we put two coats of white and three coats of clear finish on everything.

Now, on to the remaining cabinets…

20160723_141308

Spraying the cabinet doors and drawers saved A LOT of time.

20160723_140725

More doors, drawers, and trim to spray

 

20160807_100840

Halfway done. We divided the the kitchen into three sections and painted one section at a time to minimize disruption.

Before

Before

 

 

 

 

 

 

20160827_200718

After. The end cabinets were lifted slightly to provide a variation in elevation. We plan to accent this further (in the future) with crown molding at the top of the cabinets and accessories, such as a glass stemware rack, underneath.

 

 

Pantry Door Storage

Pantry Door

The pantry project was one of the first things we did after we moved in.  Once we used it for a while we determined that a far amount of space was used up by small stuff.  Inspired by Shanty2Chic, we decided to make a pantry door mounted space rack and an additional storage area at the lower portion of the door.

Step by step instructions from Shanty2Chic are available here.

The build instructions are super simple, we modified the dimensions to fit our needs and the size of our door.  Many modern interior doors are hollow, the trick to attaching the racks to the door is to use hollow wall anchors like these.  hollowdooranchorsThese things really work.  Since these racks add weight to the door, we replaced a screw in each hinge, with a longer screw so that it goes through the door casing and into the 2×4 framed door opening.  

20160929_182523

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The door opens and closes super easy and makes it easy to find these small items with a simple glance.  Moving these items to the door freed up pantry shelf space.  

Once the spice rack as done, we felt like we really needed to use the lower portion of the door for additional storage.  Again, the Shanty2Chic folks had a perfect solution.  We modified their foil storage plans to accommodate larger items.  Not only did this free up more pantry shelf space, it put commonly used items at easy reach as soon as the door is opened.

pantrydoorfinal2

 

 

Bathroom Shelves

Our master bath is designed so the toilet is separate from the rest of the bathroom.  My wife refers to it as the water closet, using a fake British accent whenever she says it.  The room has an 8′ foot ceiling and looked very stark.

We decided a pair of floating shelves was just what we were looking for and decided to do them in walnut since we had some left over from previous projects.

Bathroom_before_after
14638568290142 (1)

 

 

 

 

 

 

 

Like many of our projects we used painters tape to model the placement of the shelves.  This helped to determine shelf placement before attaching the frame to the wall.

14638567713940

The shelf frames were made from furring strips.  This is the technique we used for the pantry project where the frame is attached to the wall studs and then wrapped with finished boards.

We decided to finish the walnut pieces before placing them on the shelf.  Once finished we cut them to size and attached with 18ga finish nails.  Our finished dimensions for each shelf were 37″ wide x 10″ deep x 2.5″ high.

14638587247004  14638586968093

As usual, my wife did a fantastic job decorating the space once the shelves were in place.

14638566746310

Kitchen Command Center

One of my wife’s favorite sayings, often directed to me, is “don’t put it down – put it away”.   As usual, she’s exactly right.  When things have a place to go, it’s so much easier to find them. One thing that we’ve longed for was a central location for sorting mail, paying bills and other daily tasks.   Since many of these activities are performed over the Internet we also wanted an easy way to pay bills, or look up a recipe, online.

Our kitchen had an unused corner that was screaming “use me” every time we walked by it. While the TV tray worked for an interim solution, it was screaming to be replaced as well.

PhotoGrid_1444097635803
Before and After

Our first step was to visualize a layout that would best meet our needs and maximize the use of this small (4′ x 2′) space. Painters tape is great for mocking up ideas on a wall in that it’s easy to adjust and doesn’t leave a mark. Once we had a rough feel for logistics we picked up a stock 15″ base cabinet.  This left plenty of leg room at the work area.

kitchen station mockup    kitchen mockup2
Initial mockups with painters tape and stock cabinet

After moving the tape around a few times, we decided on the following elements.
   A stock 15” four drawer cabinet
   Counter height workspace
   Bill / mail sorter
   Organization cubbie
   A low profile computer workstation with a wireless keyboard and mouse.  

Our goal with having all items wall mounted is that we’d have the full work surface available for entertaining and other special events. The white cubbie and hanging sorter were made from plywood scraps. The storage boxes and pencil holders are walnut (my new favorite).  

kitchen station final
Final result… Voila.

If you’re interested in plans for how the individual components were built, come back soon.  We are documenting these now and will post the plans once complete.

Before and After

Although we haven’t posted in a while, we’ve been busy with lots of small projects throughout the house.  The following are a highlight of recent projects, including before and after photos.

Shelving

In exploring shelving options on-line we came across a great design from Dave Wirth.  It’s a simple, yet super sturdy, design that is made with 2×4’s and OSB plywood.  This was the perfect solution to organize all the stuff left over from the move that didn’t have a home.

Basement Storage – After

Basement Storage - Before

Basement Storage – Before

These shelves are built like a tank and can handle lots of load.  Total build cost was $48.


Fireplace Mantle

Another one of the things missing in our house was the fireplace mantle.  While there was a nice brick ledge where the mantle was previously, the mantle itself was no where to be found.

Fireplace Mantle – Before and After

The solution for this project was no further away than the garage.  We had a friend give us a stack of walnut lumber.  The design is very simple, both boards are 1½” thick, the bottom board is 11” wide and the top board is 13” wide.  We glued a small piece to the end of each board so it wraps around the mantle to the wall.

The richness of the walnut came out great with a few coats of polyurethane.


Loose Trim

Having a gap between the trim and the wall really sticks out.  We had a couple of these that were very noticeable in high traffic areas, including the stairway trim.  To close the gap, we used a clamp (in reverse / spreader mode), pre-drilled pilot holes (so the board doesn’t split) and then drove trim screws through the face of the trim to the studs in the wall.`  You could use small brads to tighten the boards, however if you have traffic areas like stairs, using screws keeps the trim from loosening up from vibration.

PhotoGrid_1436064852770

Trim screws are great for tightening up loose boards, especially in areas with lots of traffic.


Gutter Guards

I remember as a kid how much I loved maple tree ‘helicopters’.  You’d throw them up in the air and they would spin all the the way to the ground.  This is the first house we’ve had with fully grown trees including a silver maple.  I now think of maple tree tree helicopters in a whole different way in that they quickly clog our gutters.

After cleaning out the same gutter three times in two weeks, something had to change.  We researched many options and decided on metal gutter guards from Invisaflow.  Both Menards and Lowes carry them [http://invisaflow.com/lock-in-gutter-guard].  These particular guards slide under the last row of singles and snap into the outer edge of the gutter.  Many reviewers commented on how these metal guards held up well,  compared to plastic guards that melted over time. Another advantage of this particular model is that they follow the angle of the roof line making it less likely for debris to accumulate on top.  We’ve had them in place now for several weeks and they’re working great.  These cost $2.50 for a three foot section, which is a fraction of what it would cost to have gutter guards installed by a contractor.

PhotoGrid_1436064733872

Maple tree helicopters look a lot better when they’re not in your gutters.


Garage Storage  – Rakes and Shovels

We needed a solution for hanging all of the shovels, rakes and other yard tools that were in the garage.  We gave thought to making hooks to hold everything individually but that takes up a lot of wall space and most yard tools are only used for a season or two.  We decided to make use of the small wall area located on each side of the garage.  The solution was simple and consisted of only three 2×4’s.  The first 2×4 is used as the back mounting board, the next two boards are mounted near the center of the mounting board with a gap in between to accommodate the handle of the yard tool.  The back side of the center boards are at a slight angle (5°) so they lean upwards keeping the tools from sliding off the end.

The size of the boards will vary based on the size of your wall and the tools you have.  In our case, the backboard was 28” wide and the center boards were 18”long with a 5” gap between them.

Yes - we live in Michigan and really do need four snow shovels.

Yes – we live in Michigan and really do need four snow shovels.

We made two of these, one for each side of the garage.  The nice thing about these racks is that they are super simple and long enough so you can rotate off season tools to the back. They took about 20 minutes to make and hang up.  We used scrap lumber, however if purchased, a single 2x4x8′ board will make one unit and only costs $2.50,

Storage Closet

We had (another) empty closet near the pantry, that for whatever reason didn’t have a door either.  After much discussion and a rough sketch, we decided to make a couple floating shelves to match the pantry that would accommodate cleaning supplies and other household products.

Rough Sketch
This was another sketch that took place over coffee – yes, this is a recurring theme.  We wanted the shelf to accommodate cleaning supplies and bulk items like paper towels.  We kept the shelves narrow to make things easy to find, while leaving plenty of room at the sides of the walls for brooms, Swiffer and other large items.

The technique for the closet shelves was the same we used for the panty project.  A simple frame mounted to the wall studs, topped with plywood which was then sanded, caulked and painted for a finished look.

House3

20150413_165859

20150413_165851

20150414_194615

To hold the broom, dustpan and other hanging stuff, we used 1″ cup hooks.  For the Swiffer WetJet, that weighs about 10lbs, we used a $1 wardrobe hook from Menards.

20150414_203234

Total cost = less than $20 for shelf boards, hooks, and paint.

It is very rewarding to have an organized closets so that everything has its place. Now I can gladly do as my wife says… “don’t put it down, put it away”.

Kitchen Pantry

Our First Real Project – The Kitchen Pantry
The pantry was the first project we wanted to tackle after moving in.  Located near the kitchen, we had an unused closet that didn’t have a door or any shelving.  We thought this space would be ideal for the pantry. 

The layout of the room was perfect for providing wrap around shelves with 9” to 12” deep shelving in the back and 6” shelving on the sides.  Having shelves with varied depths accommodated different sized items and helps avoid the trap of having shelves so deep that you can’t find what gets buried in the back.    A tempting option was to mount a rail alongside each wall and simply place a shelf board between them. We decided to go for a wider look, making a “floating shelf” capable of supporting heavy loads without having to use shelf supports.

20150222_193506

 

 

Here we go.

We made a visual mock-up using painters tape.  We then grabbed boxes and cans of food to determine optimal height between the shelves.

 

 

Building the frame.   We thought about using 2×2’s but ended up setting up the table saw for 1 and 1/16” and ripped 2×4’s into three strips per board.  The frame was attached to the wall studs then assembled with screws and wood glue for extra strength.  Our original plan was to provide 6 shelves, two of which were to accommodate short items like canned goods.  In performing a final mock-up we ended up going with 5 shelves with more room in between.

20150322_203236

20150331_194553

20150331_194546

 

 

 

 

 

 

 

We used ½” plywood for the top and ¼” plywood for the bottom.  The bottom board wasn’t required but we wanted a finished look.  A piece of face trim hides the frame and plywood edges for a clean built-in look.

20150406_074402 20150406_074421

 

 

We finished up by sanding, caulking and painting.

 

 

 

 

20150406_185155 20150406_185207

 

Voila! Each finished shelf is just over 2 inches thick and because the back and side shelves are tied together, they provided the wrap around look we were going for.

Total Cost = < $125 (including the closet door, trim and shelves).
Value of getting boxes of food off the floor  = priceless

Knocking out the small stuff

Welcome to our first blog post.  We’ve been moved in for a couple weeks and are so excited to be here.  Our first project is really a bunch of little projects, taking care of things that need to be addressed right away.  Since the house was a foreclosure we knew we’d need to address these items as soon as we moved in.

No shower heads
Replacing a shower head is an easy job.  We spent a lot more time researching shower heads than the 2 minutes it took to install them.  Thanks to Amazon reviews, we selected the Speakman Anystream (S-2005-HB).  14261271787020

This shower head is listed as a hotel spec shower head, with Speakman being a supplier to many hotel chains.  Shower heads in the U.S. must meet conservation guidelines so they use no more than 2.5 gallons per minute (gpm).  Many folks complain about low water pressure and remove the aerator that restricts water flow to provide more pressure.  We picked this water head based on reviews that praised the water pressure and adjustable spray pattern without compromising water conservation.  The performance of this shower head is fantastic and meets the approval of the toughest shower head critic there is, at least in this family, my wife. 

Shower Rods
You guessed it, the shower rods in each bathroom were missing as well.  We decided to go with curved shower rods.  We chose fixed mounted shower rods.  We have had bad experiences with tension rods that eventually loosen up and mar up the wall. The process for installing a shower rod is very straightforward and doesn’t require many tools.  One trick that helped simplify mounting the brackets was to make a paper template of the mounting bracket hole patterns and the cap that covers it up.

LED Lights
Switching out the recessed lighting fixtures with an LED replacement is a simple project that makes a big difference both aesthetically and in energy savings  We decided to use a one piece LED light with a built in trim ring to replace missing light bulbs in recessed (can light) fixtures. Since the unit is one piece, there is no unsightly gap between the bulb and the trim ring.  The light quality of these units is fantastic and consumes 11 watts of electricity while providing much better light output than the 65 watt flood lamps they replaced.  These units are rated for 50,000 hours which means that if we use them 8 hours a day, every day of the year, they should last 17 years.  They are especially well suited for high locations, like our 18 foot living room ceiling.  In reviewing many brands and options, we chose Commercial Electric LED lights from Home Depot.  At $35 for a two pack they are more pricey than your standard flood lamp, but considering the energy they save and the fact they replace the poor fitting trim rings I had before, they are a great value.

14261286320280

These lights are designed for use in high moisture areas such as bathrooms and outside.

PhotoGrid_1426944887008

 

 

Installing them is a piece of cake. Simply remove the trim ring and existing flood lamp from the recessed light fixture, screw the power connector into the light bulb socket, and lock the unit in place with the attached mounting clips.